1.5/2.5HP In/Above Ground Swimming Pool Pump Motor Hayward w/ Strainer 115-230V

Description

Description
This swimming pool pump is made with heavy-duty, corrosion-proof construction. The stainless steel motor shaft is constructed with a reinforced thermoplastic body for longer life and durability. Advanced engineering provides high efficiency and minimal noise. This wonderful swimming pool pump will surely keep your above ground and inground pools clean.
Please connect only to a grounding type receptacle protected by a ground-fault circuit-interrupter (GFCI). To reduce the risk of electric shock, install at least 10 feet from the inside walls of a pool. Do not use an extension cord. This pump is for use with permanently installed pools only-Do not use with storable pools.
Note:
Our machine does not allow you to disassemble the cable. This product is the highest standard of UL certification. If you wire it yourself, the machine will not work properly. Thank you for your cooperation.
How to use
1.Locate the pump as close as possible to the pool.
2.The pump suction line should not be smaller than the pressure line. All piping must be airtight
3.The threads on the pump must be sealed with Teflon Tape or Silicon, when the pump unions are screwed on.
4.The weight of the piping should be supported independently and not carried by the pump.
5.Fill the pump tank with water before starting.
6.High suction lifts, or long suction lines, require additional time and reduce the performance of the pump.
7.The water being pumped cools and lubricates the seal.
8.After the pump tank has been filled with water, and the motot started, allow a few moments for the pump to start delivering water.
Attention!!
The installation must be according to the normal power indicated on the label.
The amperage must not at any time exceed the value indicated on the label
It is recommended that you consult a state-registered electrician.
Place the pump in a dry area with good ventilation.
The ambient temperature must not exceed 40℃
The pumps are only suitable for counter-clockwise rotation when viewing from the pump end.Three phase motors can rotate in either direction.Interchanging any of the cables on a three-phase motor will reverse the rotation.Momentarily start,or bump the motor without water in the tank,to check the rotation of the pump shaft.
Before disconnecting electrical connections,shut off electricity at its source.Newer work on pump without making certain the power is OFF.
This appliance is not intended for use by persons,including children with reduced physical,sensory or mental capabilities or lack of experience and knowledge,unless they have been given supervision or instruction concerning use of the appliance by a responsible for their safety
Children should be supervised to ensure that they do not play with the appliance
Problem Description:
1,The Pump Pressure is low; The Pump loses Pressure after being energized; Pump is running, But no water coming out.
Causes:
The pump head is not filled with water, causing the pump to run without water.
During the installation process of the pump, the inlet and outlet pipes are not tightly sealed, and the air leaks inside the pump head. During the operation, the air inside the pump head is pulled in, resulting in insufficient internal pressure, weak pump pressure, no pressure on the pump, no water
Solution:
When pumping water, the pump head is filled with water; the pump head transparent cover is tightened; the water pumpinlet and outlet joints are installed, and the raw material belts are tightened when the pipes are installed to prevent air leakage at the joints of the pipes.
Before pumping, the pump head should be filled with water.
Inlet and outlet joints wrapped around the raw material tape, beware of leaks.
Tightening when installing the inlet and outlet, beware of leaks.
The pump head transparent cover is tightened to prevent air leakage and water seepage
2,Pump motor trip
Causes:
1,The water pump motor enters water or pump operating environment is excessively humid, and causing the motor to short-circuit and burn.
2,The pump prevents the inlet from entering the water and burns the motor
3,There is Water in The Pump
Causes:
Our company carries out a full inspection (pumping) of the water pump, and it might result in some package still leave some water in it, It is normal.
4,The Pump stop working suddenly
Causes:
Our company's products are equipped with temperature protection device, when the motor temperature is too high, the temperature protection device will start, It will stop pump working, if the motor is shut down in the normal operation process , generally there is foreign matter inhalation in the pump, resulting in the impeller stuck, motor temperature rise , pump stop working.
Solution:
Clean up the waste inside the filter screen of the water pump regularly to prevent the waste foreign matter from flowing into the water pump to jam the impeller.
Disassemble the pump body, clean up the foreign matter on the back of the pump body to ensure that there is no foreign matter blocking the impeller, and re-assembly can be reused.
The foreign matter of the pump impeller and the diffuser is matched with the foreign matter, causing the impeller to be stuck and cleaning the foreign matter.
Features:
1.5HP&2.0HP 110-240V Swimming Pool Pump:
Brand new
This Swimming Pool Pump has a ETL/CSA Certification to ensure recognized Standards for Safety
High performance, energy saving motor with stainless steel shaft could stand wear and tear
Thermally protected motor for greater protection and longevity
Extra-large debris basket keeps pool maintenance to a minimum, letting you enjoy your pool more, while the clear cover lets you see exactly when the basket needs cleaning
Easy start up fill pump with water upon first use to prevent motor from overheating
Transparent cover helps to judge if the basket needs clean or not
Massive strainer basket holds extra capacity
Suggested Installation: 24"-26" sand filter and above-ground pools
304 grade stainless steel motor shaft,Powerful Pool Pump heavy-duty, high-performance motor with air-flow ventilation for quieter, cooler operation
Strainer basket to minimize how often you have to empty it
See-through strainer cover for a fast and easy check of the strainer
Easy-thread strainer housing ring makes cover removal extremely easy
Dependability with carborundum and graphite mechanical seals and components molded of corrosion-proof, reinforced thermoplastic
Convenient drain plug makes winter maintenance easy
High Efficiency Impeller maximize flow and reduce noise while the energy efficient motor with commercial-grade frame; Internal Inlet Fitting: 1.5" NPT (fit for 1.5" male threaded adapter)
Lifetime Warranty
2.5HP 110V Swimming Pool Pump:
Powerful Self-Priming IP55 2.5HP Electric Motor, low noise with quiet operation and no leak.
Suitable for pools up to 100,000 litres.
Advanced S-Tek Flow System For Increased Efficiency With Continuous Flow Rate Of 560L/min.
Full Size Removable Strainer Basket.
100% Salt and Chlorine compatible.
Full Commercial Duty - Designed to run 24/7.
Works with In ground and Above Ground.
Built-In Thermal Overload Protection.
Ideal for Residential/Commercial Swimming Pools & Spa's.
CE Certification.
Lifetime warranty
Specification:
1.5HP 110-240V:
Type : Pool Pump
Dual voltage : 110-120V/220V-240V
Power : 1100w
Ampere : 10A/5A
Horsepower : 1.5 HP
Speed : 3450 RPM
Max. Flow : 6500 GPH
Max. Temp : 104 Degree Fahrenheit (40 Degree Celsius)
Frequency : 60HZ
Qmax : 410 L/min
Hmax : 15.5 Meter
Power Cord : 59"
Internal Thread diameter : NPT 1.5"
External Thread diameter : G2.25"
Certification : CSA and ETL
2.5HP 110V:
Model : SPPE 250
Power : 1850W/2.5HP
Voltage : 110V / 60Hz
Ampere : 16A
Max. Flow : 560 L/m
IP55 INS CL.F : Max. 50 C
Amps : 6.8
Head : Max 19m / 62.34ft
Capacitor : 25 F
Inlet : 1.5" Internal
Outlet : 1.5" Internal
Pipe Compatibility : Fit 1.5 inch plumbing internally
Noise Level : <65dB
Thread diameter : G2.25"
Weight : 10.2 kg / 22.5 lbs
2.0HP 110-240V
Type : Pool Pump
Dual voltage : 110-120V/220V-240V
Power : 1500w
Ampere : 13.6A/6.8A
Horsepower : 1.5 HP
Speed : 3450 RPM
Max. Flow : 6500 GPH
Max. Temp : 104 Degree Fahrenheit (40 Degree Celsius)
Frequency : 60HZ
Qmax : 430 L/min
Hmax : 15.5 Meter
Power Cord : 59"
Internal Thread diameter : NPT 1.5"
External Thread diameter : G2.25"
Certification : CSA and ETL
Warranty : Lifetime
Package Includes
Swimming Pool Pump    X    1
Connector                       X    2
Manual                            X    1
About US
Our company is a leading professional eBay Megastore headquartered in California, We deliver a wide range of products, from Industrial supplies to economical lifestyle goods, to provide you with a premium eBay experience.
We offer detailed product descriptions and images to give you a real advantage in finding the products you're looking for. We strive to deliver a wide range of unique and high quality products, sourced directly from top manufacturers and sold at bargain prices.
With a cutting edge online operating system and fantastic customer support, buyers are guaranteed to receive quick replies to enquiries, prompt delivery to your home or business, and outstanding after-sales service.
Payment
1.We accept Paypal payment only.
2.Payment should be completed within 3 days of auction closing. Or unpaid dispute will be filed for closing auction.
Shipping
We have Five warehouses located in CA, TX, NY, NJ & GA. And we will choose nearest one to ship your item.
We aim to dispatch all products within one working day after your full payment is made. If you need to cancel a purchase after the product has been dispatched, please note that the postage fee may not be refundable. Additional postage fees may apply for re-delivery or re-direction requests.
Orders placed on weekend will be shipped within 2 days.
Some products may be dispatched in more than one carton.
International Buyers – Please Note:
Import duties, taxes and charges are not included in the item price or shipping charges. These charges are the buyer’s responsibility.
UPS/FEDEX: 3-5 business days. | USPS: 2-6 business days. | Truck company: 3-8 business days.
We only ship to the Lower 48 states, and we do not ship to FPO, APO or PO Box addresses.
Returns and Warranty
We provide return & refund service within 60 days after the buyer receives the product. (product kept in original condition, a restocking fee may apply).
We guarantee the product to be new and free of manufacturer defects for 1 year for the original purchaser only.
If you have a problem with the product. Please contact us through eBay and include the original purchase information (i.e. your name , address, email and purchase receipt number).
We will require a picture of the damaged part for verification.
We will repair or replace, at our discretion, any unit determined to be faulty within the warranty period.
The unit warranty does not cover accidents, develop a fault due to misuse or improper installation.
The buyer will be liable for the shipping costs associated with warranty claim.